Sound Isolation Booth Plan Drawings

Download Article

Download Commodity

A homemade recording berth can be a smashing option when you want to record vocals or audio-visual instruments. In order to build a recording booth yourself, you'll demand some general knowledge of carpentry and experience with basic dwelling improvement projects. Yet, with the right tools and know-how you tin complete this projection in a week or two. Think of building a recording booth as adding a small room to your domicile, with a lot of the same steps similar framing the walls and putting up drywall. Feel free to contract out whatever parts of the project you don't experience comfortable tackling yourself.

Things You lot Should Know

  • To make the project easier, build your recording booth in the corner of a room that already has lights and ability outlets.
  • Remember to leave a space for the door and install your audio and electrical outlets when y'all construct the framing for the booth.
  • Fill up the spaces between the framing studs with fiberglass insulation to help make the room soundproof, then hang the drywall.
  • Make your recording booth even more soundproof by mounting audio-visual tiles to the walls after you build them.
  1. 1

    Cull a corner of an existing room to build your recording booth in. Select a corner of a room where yous want to build your recording booth so yous only have to construct 2 walls. Pick a corner with exterior-facing walls if possible considering they are generally thicker and more audio-proof.[1]

    • This applies to building a rectangular recording booth from the ground upwardly. You volition demand to have bones knowledge of carpentry including framing and drywalling in club to build the booth. If y'all don't have the tools or know-how to do information technology yourself, hire a contractor to build the booth for you.
    • Brand sure the room you lot select has a solid floor as well. For case, a ground floor or a basement is a good choice. A room on an upper floor is non platonic as these floors are not as stable, which tin be bad for recording if the flooring vibrates or makes creaking noises.

    Tip: You lot tin apply the same concepts for building a rectangular recording booth in a corner to edifice booths of other shapes in corners, such equally a pentagon or triangle-shaped booth.

  2. two

    Select a corner with an existing light fixture or outlet if possible. Build the booth around an existing light fixture if you can to provide low-cal within the berth without the added piece of work of installing a new fixture in the ceiling. Construct the berth in a corner with an existing wall outlet to provide more than sources of electricity in the booth that you lot can plug a lamp or sound equipment into.[2]

    • If edifice the booth around an existing light fixture isn't an option, you tin can run some LED lighting strips around the ceiling and floor of the booth for calorie-free.

    Advertisement

  3. 3

    Measure the room and notice the studs in the corner walls. Use a tape measure to measure out the length, width, and tiptop of the room and write down the measurements. Apply a stud finder to locate the studs in the 2 walls of the corner that you program to build the booth in and mark their positions on the wall with a pencil.[3]

    • You tin can draw a crude sketch of the room and write down the measurements and stud positions if information technology's easier for you to visualize the berth that way.
  4. 4

    Make the booth a size that fits in the room and lines up with wall stud locations. Plan for i short wall and 1 longer wall, of most 1.5 times the length of the short wall, to make a rectangular booth. Brand the walls long enough that they volition line up with studs in the existing walls to screw them into.[four]

    • A good standard size for a rectangular recording booth is 4 ft (1.2 m) past 6 ft (one.8 one thousand). All the same, adapt the size based on the space you have available and the positions of the studs in your walls.
    • Think about the kind of recording you lot want to do when planning the size of the booth too. For example, a 4 ft (1.2 thousand) past six ft (1.8 m) berth is best suited to solo vocalists or acoustic artists, or maybe 2-person bands. If you want to be able to tape a larger band, yous might want to remember about converting an entire room into a recording studio rather than building a booth.

    Advertisement

  1. 1

    Buy a door for your recording berth and note down the measurements. Pick out and buy a door earlier you construct the frame. Yous will use the measurements to build a crude opening for the door into 1 of the wall frames.[v]

    • A door with a drinking glass window at the top or even a door that is by and large glass is a good option for a recording berth and so y'all can permit some calorie-free into the berth and accept visibility between the booth and the surrounding room.
  2. ii

    Construct the frames for the walls. Build the shorter wall and the longer wall out of 2 in (5.1 cm) by iv in (10 cm) pieces of lumber and screw the pieces together using four in (ten cm) forest screws and a power drill. Make the walls as tall as the room'due south ceiling height, which is unremarkably about 8–9 ft (two.4–2.7 1000).[6]

    • For example, if your recording booth is going to exist four ft (i.2 m) past 6 ft (one.8 yard), build 1 wall that is 4 ft (1.2 m) long and 1 that is half dozen ft (1.8 m) long.
    • You can either cut the lumber to size yourself or have it cut for y'all at a dwelling improvement center or lumber yard.
  3. iii

    Build a crude opening for the door into 1 of the walls. Construct a door frame that is 2 in (5.1 cm) wider than the width of the door and 2 in (5.i cm) taller than the superlative of the door. Make it out of two in (5.i cm) by four in (ten cm) lumber as with the rest of the wall frames.[7]

    • For case, if the door is a standard fourscore in (200 cm) by 36 in (91 cm) size, make the rough opening 82 in (210 cm) past 38 in (97 cm).
    • Note that this stride must be done simultaneously with building the wall frames.
  4. four

    Spiral the frames into studs in the existing corner walls and into the floor. Stand the longer wall in identify, lining it up carefully with the stud in the wall that you planned for, and so spike information technology to the stud using 4 in (ten cm) wood screws and a power drill. Echo this for the shorter wall and screw the 2 wall frames together where they meet. Spiral the bottoms of the frames into the floor as well.[viii]

    • Take someone assistance you hold the walls up and steady while you lot drive the screws into place.
    • If the floor of the room is a standard wooden flooring, use wood screws to secure the frame to the floor. If you are building your booth somewhere like a garage or basement with a cement floor, use masonry screws.
  5. 5

    Attach electrical boxes for an sound outlet and electrical outlet to the frame. Nail or screw 1 electric box for the electric outlet to a axle of the frame, about 12–18 in (30–46 cm) from the floor. Adhere another electrical box for the audio cablevision outlet one or 2 beams over.[ix]

    • Make sure to check local electrical regulations before yous install the electrical boxes. If y'all aren't certain, consult a licensed electrician.
    • Unless you have experience with electric work, it's best to get an electrician to do the actual wiring for you. You lot tin can go ahead and install the electrical boxes on the frame if you want, but take a licensed electrician finish the wiring piece of work.

    Advertisement

  1. 1

    Stuff R-19 fiberglass insulation betwixt the studs of the booth'south walls. Cut pieces to fit between the studs from a coil of R-19 fiberglass insulation using a utility pocketknife. Fill up in all the spaces between studs with the insulation.[x]

    • Fiberglass insulation comes in rolls that are 16 in (41 cm) wide, the standard width betwixt wall studs, and so it will fit perfectly betwixt the studs and stay in identify.
    • You lot can purchase special soundproofing insulation instead of standard fiberglass insulation if your budget allows for information technology. Withal, fiberglass insulation tends to work just as well and is much more affordable.
  2. 2

    Hang drywall within and outside of the walls. Cut pieces of drywall to fit the walls, with holes for the electrical boxes, and attach them to the frames using drywall screws and an electric drill. Cover the drywall with three thin layers of drywall mud, letting each layer dry for 24 hours and sanding it shine before applying the next glaze.[eleven]

    • You can hire a drywall contractor to complete this part of the task for you if you don't want to deal with all the cutting, hanging, and mudding yourself.
  3. 3

    Paint the walls a color of your choice. Use a paint roller to apply a glaze of primer to both the interior and outside walls. Wait until the primer dries, then pigment over it with 1-2 coats of wall paint.[12]

    • You might desire to friction match the exterior wall pigment to the color of the walls you built the booth in and then information technology looks more like function of the room. Still, yous could pigment it a different colour if you desire it to stand out equally an accent.

    Advertizement

  1. 1

    Hang the door in the rough frame. Fit the door into the frame you built for information technology in ane of the walls. Mount the door to the frame using its provided hinges, hardware, and screws.[thirteen]

    • If it is too difficult for yous to hang the door properly yourself, rent a carpenter to practice it for you.
  2. ii

    Mount strips of wood on the within of the door frame to create door stops. Shut the door so information technology is flush with the outside wall, then mark the position of the inside edge of the door all the way around the inside of the door frame using a pencil. Cut pieces of one in (2.v cm) by 2 in (5.ane cm) lumber to fit around the sides of the frame, then nail them into identify with the edges lined upward along the marks you made on the within of the frame.[14]

    • The door stops volition ensure the door closes properly besides equally help you soundproof the berth.
  3. 3

    Stick rubberized foam tape atmospheric condition stripping around the door stops. Cut strips of rubberized cream tape weather stripping to the length of each strip of door terminate. Printing them against the edges of the door stops that face the door.[fifteen]

    • This volition help soundproof the berth by ensuring a tight seal when the door is closed.
  4. 4

    Employ acoustic cream tiles to all the within surfaces of the booth. Apply an adhesive spray to mountain acoustic cream tiles to all the within walls of the booth, as well as the inside of the door. Cutting the cream tiles to size equally needed using a utility pocketknife.[16]

    • If your door has any drinking glass in it, don't cover up the drinking glass with acoustic foam.
    • The foam tiles volition help go on sound inside the recording booth to create good acoustics. This, along with the insulation inside the walls and the weather stripping effectually the door, means that your booth should now exist pretty soundproof and ready to tape!

    Tip: Acoustic foam tiles are typically i ft (0.30 1000) by 1 ft (0.30 m) in size. Measure the full surface area of the berth'south interior walls to determine how many tiles you'll need to encompass information technology.

    Advertisement

Enquire a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertising

Thanks for submitting a tip for review!

  • Always clothing thick piece of work gloves when you lot work with fiberglass insulation to protect your easily from glass slivers.

Advertisement

Things You'll Need

  • Measuring tape
  • Pen or pencil
  • Paper
  • two in (5.1 cm) by four in (10 cm) lumber
  • Power drill
  • Power saw
  • four in (10 cm) woods screws
  • Hammer
  • Nails
  • R-19 fiberglass insulation
  • Gloves
  • Utility knife
  • Drywall
  • Drywall saw
  • Drywall mud
  • Drywall screws
  • Wall paint
  • Paint roller
  • Paint tray
  • Interior door
  • Rubberized foam record atmospheric condition stripping
  • 1 in (2.5 cm) past 2 in (5.one cm) lumber
  • Audio-visual foam tiles
  • Adhesive spray

Nearly This Commodity

Thanks to all authors for creating a page that has been read 21,469 times.

Did this commodity help you lot?

webbharcest.blogspot.com

Source: https://www.wikihow.com/Build-a-Recording-Booth

0 Response to "Sound Isolation Booth Plan Drawings"

Post a Comment

Iklan Atas Artikel

Iklan Tengah Artikel 1

Iklan Tengah Artikel 2

Iklan Bawah Artikel